BIQU MKS-BASE V1.5 Plate Controller Board for 3D Printer Ramps 1.4

Specifications:
A collection of all the functions on a single board to solve the complicated interfaces Ramps1.4 combination, problem-prone fault
Using high-quality MOSFET tube heat better
Control panel and can be connected directly Ramps1.4,2004LCD 12864LCD control panel
Net Weight:80g
Dimension:110*90mm

Note:
Before powering up again confirm whether the positive and negative reversed, if the user is due to reverse power and burn, and we do not guarantee such problems
Do not plug in case of power motor drive easily lead to burn; do not adjust the current in the motor is running. The correct approach is to first disconnect the power, unplug the motor, and then re-power, adjust potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected
MKS-BASE is to create customer base for R & D personnel Ramps1.4, Megatronics V2.0 and other open source motherboard problems especially developed to optimize the launch of a product, particularly suitable for mass production 3D printer manufacturers use as the main control board
Give full consideration to the stability, heat dissipation, ease of use issues through continuous printing reliability testing
If special needs can contact the owner with details
Supporting line can refer to: 2PIN, 3PIN, 4PIN
Could be directly connected 2004LCD or 12864LCD (remove the L-shaped adapter plate), due to the open-source design 12864LCD 2004LCD and only standardized EXP1 and EXP2 the PIN port on the horns insertion direction and there is no specific standard, so some non Makerbase production and 2004LCD 12864LCD may be inconsistent data line card port direction, in turn, need to plug to use

Package Included:
1* MKS-Base V1.4 3D Printer Controller Board
1* USB Cable

Note: The socket color is ramdon, please double confirm you do not mind before placing order.

Product Features

  • Using 4982 as a motor drive, and a 4988 performance fairly, but with SOP package, heat dissipation will be better
  • The circuit board with high-quality 4-layer, and made a special heat treatment optimization; ramps are 2 shelves
  • Using a dedicated power supply chip, support 12V-24V power input, the voltage converter chip Ramps solve the heating problem
  • Could accept 24V input, the same system power can heat the bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems
  • The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4

Click Here For More Information

Published by

3D Print Anything

3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

2 thoughts on “BIQU MKS-BASE V1.5 Plate Controller Board for 3D Printer Ramps 1.4”

  1. While it makes for a simpler solution having an integrated board that includes the stepper drivers, it’s way too easy to damage. I made the mistake the first time by moving the build table by pushing it a little faster than I should have. Bad move! It instantly rendered the driver for that stepper dead. I purchased a new one, spent some time getting it configured……could Not get the extruder stepper to move. I returned it for a new board. This one worked perfectly………for exactly enough…

  2. Great Marlin board for the price. Does everything you need and nothing more. The documentation for the product is a little lacking, but that’s to be expected from a vendor like this. There are 2 12v fan connectors on the top left of the board which are not mentioned anywhere, but extremely important. The built in stepper motors work great and are well calibrated out of the box. I would suggest doing a heat bed MOSFET in addition to this product, since there is only 1 power connector on the…

Leave a Reply