Aluoflower TMC2100 Stepper Motor Driver Super Silence Module Heat Sink for 3D Printer Parts


Description:

Features:
100% brand new and high quality.
Drive current algorithm and regulation.
1. drive current algorithm: i=Vref*1.9/2.5, the default Vref about 0.65v, so the default current 0.5A, the maximum current 1A
2. Vref measurement of Gnd and potentiometer intermediate voltage.
3. Don’t connect to the motor when measuring voltage, otherwise it is easy to burn the drivers.
4. the measurement of the voltage should be switched on. Don’t just connect the USB power supply.
Attention: please put TMC2100 drivers in the correct direction on the board.

Use of the TMC2100 drive module:
1. When use in the Ramps1.4 or MKS Gen, or Lerdge touch screen motherboard, please remove the 3 jumper cap under the socket.
2. Please pay attention to direction.
3. The heat sink directly attached to the PCB.
4. The motor direction is opposite to that of A4988 and DRV8825, please adjust the firmware or adjust the motor wiring if you want to change to 4988.
And if you use the Lerdge motherboard, please set the direction directly in the setting page of direction of the motor.

Specifications:
Name: TMC2100 Stepper Motor Driver
Color: White + Blue
Size: 2×1.5×1.2cm / 0.79×0.59×0.47in (Approx.)
Heat Sink size: 1.2×0.9×1.2cm/0.47×0.35×0.47in (Approx.)
Application: 3D printing
Quantity: 1PC (other accessories demo in the picture is not included)

Package includes:
1 X TMC2100 Stepper Module With Heat Sink

Product Features

  • 100% brand new and high quality.
  • Super silence in working.
  • Drive current algorithm: i=Vref*1.9/2.5, the default Vref about 0.65v, the default current 0.5A, the maximum current 1A
  • Size: 2×1.5×1.2cm / 0.79×0.59×0.47in (Approx.)
  • Heat Sink size: 1.2×0.9×1.2cm/0.47×0.35×0.47in

Visit The Website For More Information…

Aluoflower 220V/110V 15A Inlet Male Plug Power Supply Socket with Fuse Switch 3D Printer Parts


Description:

Features:
100% brand new and high quality.
220V/110V 15A inlet male power socket with fuse switch.
Can be used in 3D printing.
Use only with a 250V fuse.

Specifications:
Name: Power Supply Socket With Fuse Switch
Material (External): Plastic, Metal
Color: Black, Red, Silver Tone (Shown as pictures)
Size: 5×3×2cm / 1.97×1.18×0.79in (Approx.)
Cable length: 22cm/8.67in (Approx.)
Voltage: 220V/110V

Current: 15A
Application: 3D printing
Quantity: 1PC (other accessories demo in the picture is not included)

Note:
1.Transition: 1cm=10mm=0.39inch
2.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
4.No retail package

Package includes:
1 X Power Socket With Fuse Switch

Product Features

  • 100% brand new and high quality.
  • Application: 3D printing.
  • Cable length: 22cm/8.67in (Approx.)
  • Size: 5×3×2cm / 1.97×1.18×0.79in (Approx.)
  • 220V/110V 15A inlet male power socket with fuse switch.

Detailed Information available on our Homepage…

Aluoflower MK8 i3 Kit Extrusion Head Part Makerbot Extruder Prusa for 3D Printer


Description:
100% brand new and high quality

Single head geeetech MK8 extruder upgrade, with excellent quality and the best performance of DIY and professional systems.
Simply, assemble your own double extrusion head.
42mm high quality stepper motors have a high torque and less heat buildup
Guarantee of thermal insulation cotton special ceramic stability; energy saving
Direct drive, without heavy equipment, compact size and weight
Built-in special high temperature self-lubricating material
Variety of specifications to choose the best.
Extrusion nozzle Diameter: 0.4mm
Printing Material: 1.75mm
low nozzle: Approx. 24cc/hour
Shaft speed: 40 mm/s
Nozzle heating Voltage: 12V
100 K NTC thermistor, cooling fan, Operating voltage: 12V
Heater: 6mm, 12V

Operating temperature Normal: 190-250 ℃(the maximum temperature does not exceed 280 °)

Quantity:1Set

Note:
Size for manual measurement, there may be a 0 to 2 cm error, belongs to the normal phenomenon.
And due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
Package includes:
1Pc x MK8 Extruder 3D Printer Part
1pc x 4 pins cable

Product Features

  • 100% brand new and high quality.
  • Built-in special high temperature self-lubricating material
  • Direct drive, without heavy equipment, compact size and weight
  • 42mm high quality stepper motors have a high torque and less heat buildup
    Guarantee of thermal insulation cotton special ceramic stability; energy saving
  • Single head geeetech MK8 extruder upgrade, with excellent quality and the best performance of DIY and professional systems.

Visit The Website For More Information…

Aluoflower 1 Set Auto Leveling Position Sensor Kit for Anet A8 3D Printer Printing Kit


Description:

Features:
100% brand new and high quality.
Anti-jamming DC three-wire npn often open square inductive metal sensor 10-30V.
This is an auto level sensor for the Anet A8 or other Prusa i3 Models.
Comes with mounting plate and pre soldered connector so no wiring is needed, just unplug the original z stop and plug in sensor and screw into the back of printer.

Specifications:
Name: Auto Leveling Position Sensor Kit
Material: Plastic,PVC
Color: Blue
Shape: Square
Size: 1.8×1.8×3.6cm/0.71×0.71×1.42in (Approx.)
Base size: 8.5×5.8cm/3.35×2.28in (Approx.)
Detection distance: 5 mm (mm)
Work voltage: less than DC 10-30V
Output mode: NPN three-wire
Output current: 300mA
Used for: Anet A8 3D printer
Application: 3D printing
Quantity: 1 Set (other accessories demo in the picture is not included)

Note:
1.Transition: 1cm=10mm=0.39inch
2.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
4.No retail package

Package includes:
1 Set X Auto Leveling Position Sensor Kit

Product Features

  • 100% brand new and high quality.
  • Size: 1.8×1.8×3.6cm/0.71×0.71×1.42in (Approx.)
  • Material: Plastic,PVC
  • Anti-jamming DC three-wire npn often open square inductive metal sensor 10-30V.
  • Comes with mounting plate and pre soldered connector so no wiring is needed, just unplug the original z stop and plug in sensor and screw into the back of printer.

Click Here If You Need More Detailed Info…

Aluoflower Anet LCD 2004 LCD Blue Display Screen Controller Module for RAMPS 1.4 3D Printer Parts


Description:

Features:
100% brand new and high quality.
The large screen LCD display type: 4 lines 20 characters in each.
Comes with encoder, can realize parameter adjustment, choose print and file.
Plug and play, but need to modify the firmware.

Specifications:
Item Type: Anet LCD2004 LCD Display Blue Screen Controller
Model: Control Screen A2004
Color: Red+Green (shown as pictures)
Size: 16×6.5×1.5cm/6.30×2.56×0.59in (Approx.)
Quantity: 1PC (other accessories in the picture is not included)

Note:
1.Transition: 1cm=10mm=0.39inch
2.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!

Package includes:
1 X Anet LCD2004 LCD Display Blue Screen Controller

Product Features

  • 100% brand new and high quality.
  • The large screen LCD display type: 4 lines 20 characters in each.
  • Plug and play, but need to modify the firmware.
  • Comes with encoder, can realize parameter adjustment, choose print and file.
  • Size: 16×6.5×1.5cm/6.30×2.56×0.59in (Approx.)

Visit The Website For More Information…