[sg_popup id=1]

WGCD 10 PCS Endstop Mechanical Limit Switch with Cable for 3D Printer RAMPS Prusa Mendel RepRap CNC Arduino Mega 2560

Specification:
Connections:
1, Red Line Connecting VCC (Ramps of +)
2, Connect the black wire GND (Ramps of -)
3, Green Line connection SIGNAL (Ramps in s)
Cable Type: 22 AWG
Cable Length: 70cm
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Package Csontent:
10 * Mechanical End Stop Endstop Limit Switch

Product Features

  • Mechanical endstop limit switches with 22AWG Cable for 3D Printer RAMPS 1.4 Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280.
  • Red line connecting VCC (ramps of +), Connect the black wire GND (ramps of -), Green Line connection SIGNAL (ramps in s)
  • Easy to install, common styles, replacement endstop for RAMPS 1.4, CNC and other 3D printer controllers.
  • Cable Length: 70cm/27.55inches
  • Package Content: 10 * Mechanical End Stop Endstop Limit Switch with Cable.

Visit The Website For More Information…

Quimat Arduino CNC Shield Contoller Kits for 3D Printer,CNC Shield V3.0 + UNO R3 Board + Nema 17 Stepper Motor + A4988 Stepper Motor Driver + Heat Sinks,Perfectly Compatible with GRBL

CNC Shield V3.0 features:
Latest Arduino CNC Shield Version 3.0.
GRBL 0.8c compatible.(Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
4-Axis support(X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis(6 in total), Spindle enable and direction Coolant enable

Stepper drivers
Uses removable Pololu A4988 compatible stepper drivers.
Jumpers to set the Micro-Stepping for the stepper drivers.

Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Stepping Motor
The most popular Nema 17 model with 1.8 deg. step angle (200 steps/revolution)
0.4A rated current/phase, allowing for a holding torque of 26Ncm(36.8oz.in)
Connection:Black(A+), Green(A-), Red(B+), Blue(B-)

Stepping Motor Specification:
* Cable length: 11.8 inches
* Phase Resistance: 30ohms
* Inductance: 37mH+/-20%(1KHz)
* Frame Size: 42 x 42mm
* Body Length: 34mm
* Shaft Diameter: 5mm
* Front Shaft Length: 20mm
* D-cut Length: 15mm
* Number of Leads: 4
* Lead Length: 300mm
* Weight: 230g

Kit list:
1x CNC Shield V3.0
1x Keyestudio UNO R3 board
4x A4988 driver
1x USB cable
1x Nema 17 stepping motor

Product Features

  • CNC Shield V3.0 Features – Latest Version 3.0, GRBL 0.8c compatible, 4 Axis supported and 2 end stops for each axis.
  • Compact design – Stepper motors can be connected with 4 pin molex connectors or soldered in place.
  • Stepper Drivers – Uses removable Pololu A4988 compatible stepper drivers, jumpers to set the Micro-Stepping for the stepper drivers
  • Stepping Motor Included – Nema 17 model, holding torque of 26Ncm(36.8oz.in), 12V/0.4A and 1.8 deg.step angle(200 steps/rev)
  • Technical support – Our technical support team is on standby to provide solutions to your questions, please feel free to contact us.

Click Here If You Need More Detailed Info…

AVOLUTION 444 LED Cube Light Kit with for Arduino Diffuse Blue Light,LED Cube Light Kit

Form Color: White
Model: TS-68
Quantity: 1
Material: FR4+ABS
Chipset: NO
English Manual / Spec: No
Download Link : http://7326097.s21d-7.faiusrd.com/0/ABUIABA9GAAgupuhvQUowL6gigI =KS182+4x4x4+LED+Cube+kit+with+Arduino1.pdf&v=1470647738
Other Features: We sell this kit in parts, you should assemble it yourself. Includes Controller board (Arduino compatible) Simple assembly using a PCB frame
Packing List: 1 * Control panel
1 * Soldering jig
1 * Acrylic chassis
1 * Acrylic crown sheet
4 * Acrylic side plates
16 * Stand horizontal plate
8 * Stand upright column boards
4 * Copper bushes
4 * 3*10 inner-hexagon screws
4 * 3*6 inner-hexagon screws
8 * 3M nuts
1 * USB cable
1 * Dupont Line

Product Features

  • For ARDUINO starters, we’d love to do projects that would blow people’s mind off. But without certain basic knowledge of electronics, we may find it difficult to do complicated projects such as robots, 3D printers etc.

Visit The Website For More Information…

RAMPS 1.4 Controller + MEGA2560 R3 board + 5pcs Soldered A4988 Stepper Motor Drivers + 5pcs Heat Sinks + 19pcs Jumpers with USB Cable For Arduino RepRap 3D Printer Kit

Specifications:

RAMPS 1.4 Size: 9.1 x 5.9cm / 3.58 x 2.32″

Mega R3 2560 Size: 10.8 x 5.5cm / 4.25 x 2.16″

A4988 Color: Green

A4988 Quantity: 5pcs

Package Includes:
1 x RAMPS 1.4 Board
1 x Mega 2560 R3 Board
5 x Soldered A4988 Drivers
5 x Heat Sinks
1 x USB Cable
19 x Jumpers

Product Features

  • RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion
  • Mega 2560 control board is an ATmega2560 as core micro-controller development board itself has 54 digital I/O input/output terminals (14 can be used as PWM outputs), 16 simulation than the input side, group 4 UARTs (hardware serial ports), 16 MHz crystal
  • RAMPS is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
  • With the boot-loader, download the program directly via USB without having to go through other external writer
  • After connecting this panel to your RAMPS, you don’t need your pc any more. The smart controller supplies power for your SD card. All actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller

Click Here If You Need More Detailed Info…

keyestudio MKS GEN 1.4 3D Printer controller Board /RAMPS 1.4 + Mega 2560 for Arduino (Black &Environmental-protection)

Intruduction
Keyestudio 3D MKS Gen V1.4 printer motherboard control board combines and improves the assets solution of the RAMPS 1.4 and Arduino Mega 2560 board on a fantastic single board.
Keyestudio 3D MKS Gen V1.4 printer motherboard control board is an optimal 3D printer controller solution for your Reprap 3D printer.

Features
Integrate 2560 and ramps1.4 in a board, to solve the complicated interfaces and broken problem of Ramps1.4 combination.
Replaceable motor driver, support 4988 driver and 8825 driver.
Circuit board using high-quality 4-layer board, and specially dealing with thermal optimization; ramps is a 2-layer board.
Using high-quality MOSFET tube, with better heat dissipation.
Using a dedicated power chip to support 12V-24V power input, to solve the problem of Ramps voltage converted into chip heating.
To accept 24V input, hot bed current can be reduced to 1/4 under the same system power, effectively solve the heating problem of hot bed MOS tube.
Firmware can use open-source firmware Marlin, and its configuration is exactly the same as ramps1.4, which can directly replace Ramps1.4.
Can directly connect to Ramps1.4,2004LCD control board and 12864LCD control board.
Set aside the motor pulse and direction output port, convenient to facilitate external high current to connect external high current (such as 2A, 5A) motor drive circuit.
Reserve the Servos, AUX-1, AUX-2 interfaces on Ramps1.4, providing three 5V output, three 12V output interface.
This board is an upgrade part of the MKS Gen V1.2 board, improving the performance of power protection and USB communication stability.

Package Included: 
1 x MKS-Gen V1.4 Controller 
1 x Usb Cable

Product Features

  • It gathered mega 2560 and ramps1.4 on a same board, hardware & software included, just scan the Qr code on the picture to get the wiki tutorial and software
  • Support 4988 driver and 8825 driver, Support 12V-24V power input; Firmware can use the same configuration as ramps1.4
  • Can directly connect to Ramps1.4,2004LCD control board and 12864LCD control board
  • Reserve the servos, AUX-1, AUX-2 interfaces on Ramps1.4, providing three 5V output, three 12V output interface
  • keyestudio MKS GEN 1.4 is manufactured from environmentally friendly materials and technologies, made function,voltage, current testing before packaging

Visit The Website For More Information…