ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories(Pack of 2)

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
2xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module
  • Note: Any issue please contact us before, we will always here to help!

Detailed Information available on our Homepage…

Longruner GRBL CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver With Heatsink for Arduino Kits (Arduino Kits)

CNC Shield Board:
Latest Arduino CNC Shield Version 3.0
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader – included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz

A4988 Stepper Motor Driver:
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;

Low RDS (On) Output :
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).

Package Contents:
1 x CNC Shield Board
1 x UNO R3 Board for Arduino
4 x A4988 Stepper Motor Driver
4 x Heat Sink

Product Features

  • Latest CNC Shield Version 3.0 for Arduino.
  • Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2.
  • PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC.
  • 2 x End stops for each axis (6 in total).
  • 4Pcs A4988 Stepper Motor Driver with radiator.

Click Here If You Need More Detailed Info…

ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
1xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module

Detailed Information available on our Homepage…

Hot Bed MOS Tube,Hot Bed Power Expansion Board / MOS Tube High Current Load Module / Heatbed Power Module for 3D Printer Heating Bed Accessories by Drillpro

▶Specification◀:
▶Condition: 100%Brand new and high quality

▶ Dimensions: 50*60mm

▶Weight: about 40g

▶ HIGH current load module hot bed Power expansion board / Heatbed power module / mos tube for 3D Printer.

▶ HIGH-POWER module thermal bed, completely solve the thermal power is too large bed, load current issue.

▶This module under the premise of normal cooling, found at I (Max) -25A situation stable work. During use, do not exceed current 25A.

▶Type: hot bed Power expansion board

▶ Package Contents:◀

▶ 1 X Hot bed Power Module

Product Features

  • ▲ Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • ▲ Completely solve the hot bed power is too large and the load current issue.
  • ▲ General Add-on Heated Bed Power Expansion Module.
  • ▲ With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A.
  • ▲ Please choose the appropriate power according to the power of the hot bed, leaving enough margin. High-power hot bed is recommended to use 24V power supply, so that the same power requirements, the current is 12V smaller.

Detailed Information available on our Homepage…

3D Printer Engraving Expansion Board Kit Controller CNC Shield V4+Nano 3.0 Board+A4988 Driver with USB Cable for Arduino

Why this kit?

CNC Shield V4+Nano 3.0 Board+A4988 Driver as a driver expansion board, can be used for engraving machines, 3D printer, and It is a total of three slots, can drive three A4988 stepper motor.

Specifications:

V4 Board Size: 7.2 x 5.9cm / 2.83 x 2.32″

Improved Nano Board Size: 4.3 x 1.8cm / 1.69 x 0.7″

Driver Size: 2 x 1.5cm / 0.78 x 0.59″

Heat Sink Size: 0.8 x 0.8cm / 0.31 x 0.31″

Package:

1 x CNC Shield V4.0

1 x Nano 3.0 Board

3 x A4988 Drivers

1 x USB Cable

3 x Heat Sinks

 

Note:

 WE DO NOT PROVIDE ANY TECHNICAL HELP. Thank you for your understanding.

Product Features

  • – It is a flexible set, with 3 axis stepper motor driver, compatible with Arduino and most shields designed for the Arduino micro-drive laser engraving machine, three-axis CNC engraving machine
  • – Power DC5V interface and 7.5-12V voltage input, compatible with GRBL for easy service, part replacement, upgrade-ability and expansion
  • – Easy to operate: 2A can be controlled within the two-phase four-wire stepper motor, simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started
  • – Released the digital IO interface and the I2C interface, easy to connect to other modules, such as ENDSTOP, LCD I2C or other I2C module
  • – Simple step and direction control interface, taking anti-static measures before you use the A4988 modules in case of short-circuit

Visit The Website For More Information…