Heat Bed Mosfet, MACTISICAL 2 Pack 3D Printer Heat Bed Power Module 3D Printer Board Expansion Board MOS Tube High Current Load Module

100% Brand new and Premium Professional Grade MACTISICAL 3D Printer Hot Bed Power Expansion Board .

This module is based on power mosfet and will allow PID control of the heated bed (DC-DC Relays usually do not allow this).

According to the thermal power of the bed, please choose the matching power supply, with sufficient margin. High-Power heated bed is recommended to use 24V power supply,under the same power requirements, the current is smaller than 12V.

Specification
Color: Black, cable length: 6 inch
Net Weight: 75g(approx.)
Size: 2.36″ x 1.97″ x 1.2″ / 60mm x 50mm x 30mm
Mounting Holes: D=3.2MM For M3 Screws.

Notice:
Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working.

Package Content:
2*Heat bed Power Module with 2 connection cables

Support
Please do not hesitate to contact us if there’s any problem or question about our products. We will keep improving our products and service, and try our best to meet customers’ needs. Thank you for supporting MACTISICAL.

Product Features

  • ★ WELL MADE- New material with superior quality stainless, High-grade Aluminum block for best connectivity and long life.
  • ★ HIGH TRANSMISSION – With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A.
  • ★ MULTIFUNCTION – Completely solve the hot bed power is too large and load current problems,and can well protect the connectors on the controller board from overheating.
  • ★ MEET YOUR NEEDS -Widely used for common 3D printer models,extruder and other open 3D printer motherboards.such as Anet A8, etc.
  • ★ WARNING – For use on some devices (for example,Anet A8),you need to make sure the power supply is set to 110 volts instead of the default 220 volts.If the voltage is too high, the product will get super hot, even charred!! Don’t touch it lightly.

Click Here For More Information

COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module

Usage:
1. Plug a power supply.
2. Connect to heated bed.
3. Connect digital control signal to GND, D8 of MKS Mini.
4. Connect to the heated bed signal on Ramps1.4 or MKS series controller boards.

Notics:
1. Only can choose 3 or 4 signal group.
2. Pay attention to polarity.

Package includes:
1 x Heating Controllor MOS Tube

Product Features

  • Each one has been done functional test.
  • Superior performance of MOSFET (Max 280A).
  • Can use for hot bed, output signal of Ramp1.4 and MKS series to control.
  • Can use digital signal of 5-24v to control.
  • Extra large heat sink , the maximum current can be up to 30A or more.

Detailed Information available on our Homepage…

RepRapChampion 3D Printer Heated Bed Power Module High Current 210A MOSFET upgrade Anet A8, TEVO Tarantula and others

This listing is for one power module for controlling 3D printer heated bed, it is also can be used to drive other non-inductive loads. If you plan to use silicone heater of large area heated bed, you most likely will overcome limitations for the current, that can handle your current 3d printer electronics. This control board will handle high current without even getting warm. Oversize MOSFET and overall very robust PCB design will allow for trouble free operation without active cooling.

Heated bed power module features:

Based on powerful MOSFET HA210NO6.
Dimensions: 60x50mm.
Mounting holes: 3.2mm diameter, for M3 screws.
Distance between holes: 54x43mm.
Very powerful MOSFET to withstand higher current than normal RAMPS or other 3D Printer controller can handle.
Voltage: 12V-24V.
Maximum current with active cooling: 210A.
Current: 50-80A safe for prolonged times without active cooling.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this).

Package contents:

1 x Heated Bed Power Module.
1 x Connection cable for input signal.

Product Features

  • Safe and reliable way to handle high current heate bed on 3D Printer
  • Easy to install and connect with supplied connection diagram
  • It will not overheat under normal load
  • Active cooling is not required but recommend

Detailed Information available on our Homepage…

ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories(Pack of 2)

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
2xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module
  • Note: Any issue please contact us before, we will always here to help!

Detailed Information available on our Homepage…

ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
1xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module

Detailed Information available on our Homepage…