- Shaft Usage : 5mm to 8mm.
- Dimensions: 19mm x 25mm.
- Color: Silver Tone.
- Material: Aluminum Alloy.
- Package Content : 2 x Beam Coupling
●High Stability:No shaft coupling needed,integrated with stepper motor and lead screw.
●High torque Nemga 17 stepper motor:It provides 1.5A 40Ncm/57.1 oz.in holding torque
●Easy to plug:100mm stepper lead wire with XH2.54 connector,no soldering or peeling works.
●Motor rotor is covered by magnetic filling materials,which will help to refrain from skipping steps and getting stuck.
●Redrex Support:Any quality problems and support ,please feel free to contact Redrex Team directly.
Manufacturer Part Number: RDX3D060
Motor Type: Bipolar Stepper
Number of Phase: 2
Step Angle: 1.8 deg.
Rate Voltage: 3.3V DC
Phase Resistance: 2.2ohms±10%（20℃）
Phase Inductance: 3.8mH±20%(1KHz)
Frame Size: 42 x 42mm
Body Length: 352mm
Lead Screw Lengh:310mm
Number of Leads: 4
Lead Length: 100mm
Item Weight: 500g
1x 310mm T8x8 Lead Screw Stepper Motor
CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC
DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)
Nema 17 Stepper motor Specification:
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm
1 x CNC Shield Board
1 x Kuman UNO R3 Board
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board
These vibration dampers are a great motor mount accessory for 3D Printers, CNC, or other hardware that uses NEMA 17 steppers or electrical motors. Installed between your stepper and the mount with the original screws, they will drastically reduce noise and vibration transmitted through the machine. Reduced noise and vibration results in higher 3d print speeds with fewer mechanical artifacts.
Step angle accuracy: + – 5%(full step,not load)
Resistance accuracy: + – 10%
Inductance accuracy: + – 20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ———–20deg ~+50deg
Insulation resistance:100MΩ Min,500VDC
Insultion Strength——–500VAC for one minute
Step Angle (deg):1.8A
Motor Length(mm): 33MM
Rated Current (A): 1.33A
Phase Resistance (Ohm) :2.1Ω
Phase Inductance(mH) :2.5mh
Detent Torque (N.cm) : 19mm
Shaft length mm: 19mm
1x Stepper Motor