BLTouch : Auto Bed Leveling Sensor / To be a Premium 3D Printer (With 1M Extension Cable Set)

Main functions and controls of BLTouch are same as usual auto bed leveling sensor, consists of RC servo and micro switch. Thus, BLTouch can be applied on almost every board. BLTouch fulfilled simple structure and high precision by using progressively designed solenoid and hall sensor, and aimed user convenience and enjoyable printing by adding many smart functions, self-test, alarm, alarm release, test mode for M119. – Simple BLTouch can be easily applied, since it has a small and simple structure. – Smart [Self-test]: The push pin is operated three times to test when the power is on [Alarm]: The LED light blinks if a problem found on a self-test or on an operation – High-precision BLTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise. Includes 1 Meter extension cable set. No soldering required!

Product Features

  • BLTouch is an auto leveling sensor for 3D Printers based on open-source.
  • Simple, Smart, High-precision.
  • It could work with any kinds of bed materials, such as glasses, woods, metals, and so on.
  • This variation includes solder less extension cables. These plug into the original connections and extend them one meter.

Detailed Information available on our Homepage…

Kweiny Heat Insulation Cotton and PTFE High Temp Tape for 3D Printer Makerbot Hotend Heater Block | 10PCS Cotton and A Roll of Tape for Extruder Parts Tool Kit

Notice:
1. After replace the nozzle, Please recalibrate the distance between nozzle and build plate to ensure the quality of print parts;
2. Please do not use flame to test their heat resistance, because the flame’s temperature is much higher than 300 degrees Celsius (572 Fahrenheit ).

Size:
Heat insulation cotton: Length 80mm/3.15in, width 20mm/0.78in, thickness 2mm;
PTFE high temp tape: Total length 10m/32.8ft, width 8mm, thickness 0.13mm

package including:
10PCS heat insulation cotton;
One Roll of PTFE High Temp Tape

Product Features

  • Compatibility: Matches all 3D print extruder heater block offered from E3D Makerbot, MK8 Makerbot RepRap , etc.
  • High temperature resistance: Both PTFE tape and heat insulation cotton, short term resistance to temperature 260 degrees Celsius (500 Fahrenheit ), long term resistance to temperature 300 degrees Celsius (572 Fahrenheit )
  • Function: Keep heater block temperature constant, so that improving the quality of the printed matter, save electricity and prolong the service life of heater and temp sensor
  • Use-method: You can cut cotton into the right size and hole according to your needs, then stick it firmly with PTFE tape. 5 sides of heater can be wrapped up in cotton, except the surface installed heater wire, but you just need to use 1 piece cotton. You can also use PTFE tape to stick any other parts on your 3D printer
  • Material: The heating insulation cotton is made from heat resistant ceramic fiber, the tape is made from PTFE

Visit The Website For More Information…

TIANSE Wood 3D Printer Filament 1.75mm 1KG Spool Filament for 3D Printing, Dimensional Accuracy +/- 0.03 mm

Product Features

  • Material: Wood-Pla Composite – Color: Wood (25%-30% wood fill)
  • Weight: 1 KG (approximately 2.20 lbs) Spool
  • 1.75mm Filament Diameter (Dimensional Accuracy +/- 0.03mm)
  • Wood 3D Printer Filament Vacuumed Sealed With Desiccant
  • 100% Satisfaction Guarantee: 2-Year Warranty and 24*7 customer support with technical advice

Check Out Our Website For Details…

Iverntech Nema 17 Stepper Motor Bipolar 1.5A 400mN.m 2 Phase 4 Wires 1.8 Deg for 3D Printer or CNC Machine

Specification:

Motor Type: Bipolar Stepper

Rated Voltage: 3.3V DC

Rated Current: 1.5A

Phase Resistance:2.2ohms ± 10% (20 C)

Step Angle: 1.8 deg.

Phase Inductance: 3.8mH ± 20%(1kHz 1V rms)

Number of Leads: 4

Item Size: 42.5×42.5x63mm

Item Weight: 280g

Packing List:

1x Nema 17 Stepper Motor

1x 50cm Motor Wire

Product Features

  • 2 Phase 4 Wires Nema 17 Stepper Motor, with 50cm motor wire
  • Size: 42.5 * 42.5 * 63mm
  • 40Ncm/57.1oz.in holding torque
  • Current 1.5A. Voltage: 3.3V Dc
  • Widely used in Kossel and Pruse 3D printers and CNC parts

Visit The Website For More Information…

CCTREE 3D Printer Heater Block Silicone Cover MK7/MK8/MK9 Hotend For Creality CR-10,10S,S4,S5 Anet A8

Materil:Silicone

Color: coffee

Item Weight: 2g

Item Size: 22 x 22 x 15mm/ 0.66 * 0.66 * 0.6in (approx.)

Package List:
3 x Silicone Cover

Product Features

  • Made of non-stick silicone material
  • Helps to keep the hotend temperature extremely stable.
  • Can extend the life of the heater block and extruder by keeping it cleaner.
  • High temperature resistance: 280℃.
  • Professional for 3D printer extruder.

Detailed Information available on our Homepage…