[sg_popup id=1]

3D printer NTC Thermistor Temp Sensor 100K for Reprap Prusa i3 Comgrow

Package included: 5pcs thermistors
Application : Heated bed or extruder of Reprap Prusa I3 3D Printer
Resistance value at 25°C=100K
Thermistor: small size 1.25mmx2.0mm glass bead
Wiring insulation: high temperature Teflon/PTFE.

Product Features

  • Use for heated bed or extruder
  • It has 2 pin female connector
  • Wire length: 1m/39.4 inches
  • Package include: 5 thermistors
  • Temperature sensor 100KΩ accuracy of ± 1%

Detailed Information available on our Homepage…

CHPOWER 12V 40W 620 Ceramic Cartridge Heater and NTC Thermistor 100K 3950 for 3D Printer Creality CR-10 CR-10S S4 S5 Makerbot RepRap Prusa i3 (Pack of 10)

Cartridge Heater:

● Cartridge heaters is consist of a cylindrical stainless steel tube and thus provide a high corrosion prevention
● The heating wire inside which is wound onto a ceramic core
● The number of coils varies depending on the power, and provide a great uniform distribution of heat, which considerably increases the long life of the heater as well as prevents the oxidation of the heater wire even at high temperatures
● The solids, liquids, and gases need to be heated by cartridge heater, transmit heat quickly by conduction if the producer of the heat (the cartridge) is in direct contact with the heat sink (any solid, liquid, or gas)

Cartridge Heater Application:

● Widely used for manufacturing plastic and rubber parts in the car industry or in the food processing industry, etc
● Semiconductor chamber heating, semiconductor wafer lead connection, semiconductor wire and die bonding
● Freeze protection and deicing of equipment in cold climates or applications ● Humidity Control
● Patient Comfort heating used in medical devices
● Mold die and platen heating
● Seal bars used in packaging equipment
● Test sample heating in gas chromatography

Thermistor Specification

● For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
● Small Size: 1.25mmx2.0mm glass bead
● High accuracy: ±1%
● Resistance value at 25°C=100K
● Wiring insulation: high temperature teflon/PTFE
● Wiring length: 1 meter
● Operating temperature range: -40 ° C … + 300 ° C
● Dissipation power factor: ≥ 5MW / ° C (static air)
● Rated power: 45MW
● Thermal time constant ≤ 7S (static air)
● Temperature Coefficient of Resistance; -2-5% / ° C

Included:

5x 12V Cartridge Heater with 1.0m Wire
5x NTC Thermistor 3950 100k
1x Allen Wrench

Product Features

  • Cartridge Heater Material: 304 Stainless Steel, Voltage: 12V, Power: 40W. Conveniently pre-wired with 1 meter long high temperature Teflon insulated wiring
  • Thermistor Color: White, support for NTC 3950 is included in Marlin firmware, use TEMP_SENSOR 11 in firmware configuration. Temperature sensor 100KΩ accuracy of ± 1%
  • The number of coils varies depending on the power, and provide a great uniform distribution of heat, which considerably increases the long life of the heater as well as prevents the oxidation of the heater wire even at high temperatures .
  • Cartridge heater is consist of a cylindrical stainless steel tube and thus provide a high corrosion prevention.
  • CHPOWER is a TRUSTED VENDOR, we provide 12-month manufacturer warranty on all parts. Buy with confidence.

Detailed Information available on our Homepage…

RepRap MK3 Heatbed Heated bed Heat bed 3mm Aluminum PCB Board Heat bed 12V/24V Dual power for RepRap 3D Drucker Printer Prusa i3 With Thermistor & Wire

Overview
The Aluminum Heatbed MK3 have features similar to MK2 and you can also operate this board with 12V and 24V two voltage, more practical.
Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It’s a much lighter solution than PCB heatbed + glass, which makes it better for faster prints. due to the aluminum substrate material is expensive, the cost of production is often ordinary glass fiber board is expensive, so the MK3 price is more expensive.
Please note the Aluminum Heatbed can have some marks or minor scratches, but it will only be of cosmetic character and will not affect the use adversely.

Features
(1)Dual power supply. Operate at 12V or 24V. You can use thinner wires when operating at 24V.
(2)A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.
(3)Large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.
(4)Pads for SMD thermistor 1206.
(5)With 15V on the 12V terminals will maintain approx. 115 degree Celsius without regulation.
(6)Running 24V on the 12V terminals will heat up the heatbed to 100 degree in only 2 minutes
(7)Your printer controller will regulate the power to the heatbed in order to get your preset temperature.

Specifications
(1)Material:Aluminum Plate
(2)Voltage:12V/24V
(3)Max Temperature:180 Degree Celsius
(4)Dimensions:214mm x 214mm
(5)Thickness:3mm
(6)Net Weight:400g
(7)Color:Black
(8)1 Layer 35μm (1oz base) Copper
(9)Resistance between 1.4 and 1.6 ohm for the 12V
(10)Resistance between 5.0 and 5.4 ohm for the 24V
(11)100 Degree Celsius possible for both 12V and 24V

Product Features

  • (1) Dual power supply. Operate at 12V or 24V. You can use thinner wires when operating at 24V.
  • (2) A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.
  • (3) Large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.
  • (4) With 15V on the 12V terminals will maintain approx. 115 degree Celsius without regulation.
  • (5) Running 24V on the 12V terminals will heat up the heatbed to 100 degree in only 2 minutes.

Click Here For More Information

[Gulfcoast Robotics] HEX Screw-In M3 EPCOS Thermistor for 3D Printer Extruder Hotend. Working Temperature up to 300C. 2017 Version.

New 2107 Version with working temperature up to 300C. Leads insulated with fiberglass, thermistor glued with 600C rated ceramic compound.

Our Screw In Thermistor uses most popular in reprap community EPCOS B57560G104F.Hex brass body with M3x0.5 threaded stud allows you to easily screw the thermistor into a M3 hole with zero chance of it falling out halfway through a print.Simply tap the existing hole on your hot end with a M3 tap and screw in the thermistor. The thermistor leads are insulated in fiberglass Tubing, 2 Pole JST Style Connector is attached to the leads ends. Connection cable with mating JST connector for connecting with 3D printer electronics is included. Thermistor glued in housing with high temperature 600C rated ceramic glue. Maximum allowed temperature for prolonged time is 300C.

Package contents:

1 x Hex Housed Modular Thermistor assembled with PTFE tubing, JST female connector and NTC EPCOS B57560G104F 100k Thermistor.

Product Features

  • Working temperature 300C and higher, fiberglass insulated leads
  • Thermistor glued in with 600C rated ceramic compound
  • Connector type: JST 2 pin connector, 2.5mm spacing.

Click Here For More Information

Anet 3D Printer Parts, 12V 40W 620 1M Ceramic Cartridge Heater and 3950 100K NTC Thermistor for 3D Printer (Pack of 4pcs)

Features of heating tube:
Cartridge heater widely applied for 3D printer, model heating, hot-box & other heating devices.
Voltage: 12V, power: 40W.
Stainless steel material.
The wire length approx. 1 meter.
The stainless steel part, 6mm diameter, 20mm in length.

Specifications of heating tube:
Suitable for: A2/A3/A6/A8 3D Printer etc.
Material: Stainless Steel
Voltage: 12V
Power: 40W
Wire Length: Approx. 1m / 39.4in
Diameter: 6mm
Length: 20mm
Quantity: 2pcs

Features of thermistor:
NTC pre-wired thermistor for most 3D printers heat bed & extruder.
100K ohm temperature sensor.
3P terminal for connecting.
With 1m long high temperature insulated wire.
Durable material for long life.

Specifications of thermistor:
Suitable for: Anet A2/ A3/ A6/ A8/ E10/ E12 3D Printer.
Material: High Temperature Teflon(200°C)
Working Temperature Range: -40°C~+300°C
Resistance: at 25°C=100K ohm
Cable Length: Approx. 1m
Quantity: 2pcs
Package List:
2 * cartridge heater
2 * thermistor
Note:
The item only includes the cartridge heater and thermistor.

Product Features

  • Thermistor: Working Temperature Range: -40°C~+300°C;
  • Resistance: at 25°C=100K ohm;
  • Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring;
  • Cartridge Heater: Material: Stainless Steel; Voltage: 12V; Power: 40W;
  • Use for 3D Printer;

Visit The Website For More Information…