[sg_popup id=1]

Wangdd22 E3D V6 Hot End Full Kit 1.75mm 12V Bowden/RepRap 3D Printer Extruder Parts Accessories 0.4mm Nozzle

Please recognize the seller: Wangdd22
Compatibility: compatible with all 1.75mm V6 E3D Makerbot 3D printer.

Notice: Small parts, keep away from children

12V/40W heater,temperature can be up to 280°C(Long-term temperature: 240°C/ short-term temperature: 280°C)
12V high speed fan with shroud, radiating quickly
One meter long PTFE/teflon tubing 4mm OD 2mm ID
PC4-01 tube fitting
A v6 heating block
Outer thread : M6 M7
Throat outer diameter: 6mm
Throat inner diameter: 4mm
Teflon pipe inner diameter: 2mm
Length of nozzle throat: 22.5mm
Filament diameter : 1.75mm
Extruder brass nozzle input diameter: 1.75mm
Extruder brass nozzle output diameter: 0.3mm 0.4mm 0.5mm

Package including:
1 x all metal V6 hotend 12V/40W/1.75mm/0.4mm nozzle/ extruder
1 x 12V high speed fan with shroud
1 x One meter long PTFE/teflon tubing 4mm OD 2mm ID
1 x PC4-01 Tube Fitting
1 x 0.3mm nozzle print head
1 x 0.4mm nozzle print head
1 x 0.5mm nozzle print head
1 x V6 heating block
2 x teflon tube within stainless steel nozzle throat

Product Features

  • Applicability & compatibility: compatible with all 1.75mm E3D V6 Makerbot 3D printer; NTC connector with terminal, easy to intall
  • Anti-leakage & anti-blocking design: extruder nozzle connect connect with the tube seamless, prevent print material from leaking or blocking
  • Heat resistant & ventilation: 12V/40W NTC heater, avoid NTC burn and break frequently, 304 stainless steel material nozzle throat and high quality resistor whose temperature can up to 280°C, 12V high speed fan, radiating quickly
  • Specification: brass material extruder nozzles, output diameter 0.3mm/ 0.4mm/ 0.5mm, input diameter (filament) 1.75mm
  • Package include: all metal V6 hotend 12v/40w/1.75mm/0.4mm extruder full kit(V6 print head + fan + fan cover + PTFE tube + tube fitting ), 3 Pcs brass extruder nozzles(1×0.3mm/1×0.4mm/1×0.5mm), and a v6 heating block, 2Pcs teflon tube within stainless steel nozzle throat

Visit The Website For More Information…

Published by

3D Print Anything

3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

2 thoughts on “Wangdd22 E3D V6 Hot End Full Kit 1.75mm 12V Bowden/RepRap 3D Printer Extruder Parts Accessories 0.4mm Nozzle”

  1. TroubleShooting_Marlin_RepRap_High Temp Readings Fix Troubleshooting Solution right here-Marlin Firmware-RepRap-High Temp Readings- I was getting temp readings of 500 degrees and up to 793 degrees when switching the Thermal Setting in Marlin. Couldn’t find the solution anywhere (tried, forums, FaceBook, RepRap Wiki…) but it turns out the nut was tightened too much out the factory on the thermistor. Once I loosened it just a little bit, my temp went to 24 degrees which is normal for me and it heated right up. Now it works great but it was a long…

  2. If you’re having trouble with this, it’s probably not the fault of the components. Read up on printing with All Metal hot-ends! I thought this was faulty until I took some time to learn more about all-metal hotends and how to get good prints. The PTFE lined throats are best for my needs and I haven’t had a single issue with this since I swapped out the throat on the heat brake for one of the nylon lined spares that this came with. All-metal hotends require much more dramatic cooling at the heat brake than I think I was getting, and you’d want to lubricate the hotend with some oil and drastically reduce your retraction…

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.